Quality manager classifying a component finding against Appendix A to Part 43 before teardown

Major Repair vs Minor Repair: The Classification That Decides Everything Downstream

By the AeroKool Aviation team · Hialeah, Florida

Major repair vs minor repair is a regulatory classification that decides who must approve the data behind a repair, not a judgement about how difficult the work is. A major repair needs data that has been approved; a minor repair runs on data that is acceptable to the Administrator, and the whole apparatus of engineering authority sits on which side of that line the work falls.

The classification is made by consequence rather than by effort. A repair that takes four hours and a repair that takes four days can land in different categories, and the more demanding job is sometimes the minor one. Difficulty is not the test.

Getting this wrong is not a paperwork problem that surfaces at release. It is a planning problem that surfaces at teardown, because the data has to exist before the work does, and the difference between approved and acceptable data is what the classification switches between.

What the Test Actually Says

Both definitions live in Part 1, which is why people look for them in Part 43 and do not find them.

The definition in §1.1

14 CFR §1.1 defines a major repair as a repair “That, if improperly done, might appreciably affect weight, balance, structural strength, performance, powerplant operation, flight characteristics, or other qualities affecting airworthiness,” or “That is not done according to accepted practices or cannot be done by elementary operations.”

A minor repair is defined by subtraction: “a repair other than a major repair.” There is no independent test for minor, which means every classification is really a single question asked once about the major definition.

Read the grammar, because the grammar is the test

Two features of that definition do the work and both are easy to skim past. The test is conditional: it asks what might happen if the work were done improperly, not what will happen when it is done well. And it is disjunctive: either limb is sufficient, so a repair can be major purely because it falls outside accepted practices and elementary operations, without any argument about airworthiness effect.

That second limb catches more component work than most shops expect. The question is not only what the repair affects. It is also whether the repair is the kind of thing that can be done by elementary operations at all.

There is a third feature worth naming, which is what the definition leaves out. It says nothing about the value of the article, nothing about the labour involved, nothing about the number of parts replaced, and nothing about whether the shop has done the job before. Those are all reasonable things for a planner to care about and none of them is in the test. A classification argument that reaches for any of them has left the regulation and moved into preference.

The practical consequence is that the classification can usually be settled from a description of the finding and a reading of the definition, without a quotation and without a teardown estimate. That is why it can and should happen first.

The parallel definitions for alterations

Section 1.1 runs the same structure for alterations. A major alteration is “an alteration not listed in the aircraft, aircraft engine, or propeller specifications” that might appreciably affect the same list of qualities, or that is not done according to accepted practices or cannot be done by elementary operations, and a minor alteration is “an alteration other than a major alteration.”

Note the extra opening clause. For alterations, the specifications matter first; for repairs they do not appear in the definition at all. Repairs and alterations are classified by related but not identical tests, and treating them as one test is a common shortcut with occasional consequences.

How Appendix A Delimits the Categories

The definitions set the test. The appendix organizes the answer.

The structure, and why the appliance paragraph is yours

Appendix A to Part 43 is titled “Major Alterations, Major Repairs, and Preventive Maintenance” and has three paragraphs: (a) major alterations, (b) major repairs, and (c) preventive maintenance. Paragraphs (a) and (b) are each subdivided by airframe, powerplant, propeller and appliance.

For an air cycle machine, a cooling turbine, a heat exchanger, a valve or an environmental control unit, the appliance subdivision is the operative one. A shop that classifies component work against the airframe paragraph is reading the right appendix in the wrong place.

What the appendix does and does not resolve

Paragraph (b) opens by describing what it covers: “(b) Major repairs — (1) Airframe major repairs. Repairs to the following parts of an airframe and repairs of the following types, involving the strengthening, reinforcing, splicing, and manufacturing of primary structural members or their replacement, when replacement is by fabrication such as riveting or welding, are airframe major repairs.”

Read that construction carefully, because it is the model for the whole paragraph: the appendix enumerates, and the enumeration is the answer for what it covers. What the appendix does not do is anticipate every finding on every component, which is why the §1.1 test remains live for anything the enumeration does not reach. Consult the current text of the appliance subdivision rather than a summary of it, including this one.

Appendix B, and the route that applies to a repair station

Appendix B to Part 43, “Recording of Major Repairs and Major Alterations,” sets the recording obligation, opening: “Except as provided in paragraphs (b), (c), and (d) of this appendix, each person performing a major repair or major alteration shall—”. Paragraph (a) is the general route. Paragraph (b) is a specific alternative for certificated repair stations, and paragraphs (c) and (d) cover work under §43.17 and extended-range fuel tanks.

That exception matters operationally. A component shop recording a major repair the way an individual mechanic would has used the general paragraph when a specific one was written for it. Identify which paragraph your organization operates under before the first major repair, not during it.

It also has a knock-on effect that catches organizations out during an audit. Because the recording route differs, the evidence an auditor expects to find differs too, and a shop that has been operating under one paragraph while its procedures describe another produces records that are internally consistent and externally wrong. Reconcile the procedure with the paragraph once, in writing, and the question stops recurring.

The same point applies to a shop working as a subcontractor for another maintenance organization. Whose recording route governs, and who holds the record afterwards, are questions worth settling in the arrangement rather than at the release.

What Changes Once the Work Is Major

Three things, and they arrive in a fixed order.

The data standard changes

14 CFR §145.201(c) conditions approval for return to service on the work having been performed “in accordance with the applicable approved technical data or data acceptable to the FAA,” with a separate condition attaching to major repairs and major alterations. For a minor repair, the acceptable standard of §43.13(a) governs the method and the manufacturer’s manual is the ordinary source.

A minor repair asks where the method came from. A major repair asks who approved it.

That single sentence is the most useful thing to hand a planner. It converts an abstract legal distinction into a question with a name attached, and it makes the consequence of a misclassification concrete: get it wrong in one direction and you commission engineering you did not need; get it wrong in the other and you release a component on data that does not authorize the work.

The signatory changes

Once the data must be approved, someone with approval authority has to have signed it. AC 43-210A describes three recognized routes: a field approval through an aviation safety inspector, a properly authorized Designated Engineering Representative, or an Organization Designation Authorization holder. The circular is explicit that it is “an acceptable means, but not the only means,” and notes that where all the required data is already approved, no further approval is required.

Where a DER fits and what the approval looks like is the route most component work travels, and it produces a specific document rather than an opinion.

The record changes

14 CFR §43.9(a) requires the entry to contain “A description (or reference to data acceptable to the Administrator) of work performed,” the date of completion, the name of the person performing the work where different from the approver, and the signature and certificate details of the person approving it. Appendix B then adds the recording obligation for the major case.

The data reference in that first item is not decoration. It is the thread an auditor pulls, and the words used to describe the work carry their own regulatory weight.

Where the Classification Goes Wrong

Four patterns, and none of them is about engineering competence.

Difficulty substituted for consequence

The most common error is classifying by how hard the job was. A straightforward operation on a highly loaded element can be major; an intricate operation on something with no airworthiness consequence can be minor. The test in §1.1 asks about effect and about elementary operations, and it never asks about hours.

The classification made after the work

The second is sequence. A repair is completed, someone asks whether it was major, and an approval basis is sought for work already performed. That conversation is harder than the same conversation before teardown and sometimes has no clean answer.

Classification first, data second, work third. Any other order is a rework plan.

The variant of this that looks harmless is the classification made provisionally, on the assumption that a teardown will confirm it. Sometimes a teardown does change what is found, and the honest response is to reclassify and stop, not to carry the original classification forward because the paperwork was already raised. A provisional classification that hardens by inertia is the same failure with better intentions.

The alteration classified as a repair

The third is category drift. Where the work changes the article rather than restoring it, the alteration test applies, and that test opens with the specifications rather than with the effect. Restoring a component to its original condition and modifying it are different acts with different tests, and §43.13(b) frames the restoration case: the condition must be “at least equal to its original or properly altered condition.”

The classification made outside the certificate’s scope

The fourth is scope. A repair correctly classified as major, with approved data in hand, still cannot be performed where it falls outside the shop’s ratings. Section 145.201(b) is unambiguous: “A certificated repair station may not maintain or alter any article for which it is not rated, and may not maintain or alter any article for which it is rated if it requires special technical data, equipment, or facilities that are not available to it.”

Classification answers what the data must be. It does not answer whether you may do the work.

Questions to Settle Before Teardown

Ask these in the order given, because each one depends on the one before it.

Questions about the classification itself

Is this work a repair or an alteration? Against which subdivision of Appendix A to Part 43 is it being classified, and is that the appliance subdivision? Which limb of the §1.1 test is being relied on — the airworthiness-effect limb, or the accepted-practices-and-elementary-operations limb? And who in the organization makes the call, on what record?

Questions about what follows from it

If the classification is major: what approved data authorizes the work, and by which of the three routes was it approved? Which paragraph of Appendix B applies to your organization’s recording? Is the work inside the ratings, the operations specifications and the capability list? And if approved data does not exist and cannot be obtained in the time available, is replacing the component the better answer than repairing it, or does a Parts Manufacturer Approval open a route that repair does not?

Frequently Asked Questions

what makes a repair major rather than minor?

The test in §1.1 has two limbs and either is sufficient. A repair is major if, improperly done, it might appreciably affect weight, balance, structural strength, performance, powerplant operation, flight characteristics or other qualities affecting airworthiness, or if it is not done according to accepted practices or cannot be done by elementary operations. A minor repair is defined simply as a repair other than a major repair.

is a difficult repair always a major repair?

No, and this is the most frequent misreading. The test asks about consequence and about whether the work falls within accepted practices and elementary operations. Labour hours, tooling complexity and technician skill are not part of the definition, so a demanding job can be minor and a quick one can be major.

where are major repairs listed?

Appendix A to Part 43, in paragraph (b), subdivided by airframe, powerplant, propeller and appliance. For component work on an air cycle machine, a heat exchanger or a valve, the appliance subdivision is the operative one. Where a finding is not reached by the enumeration, the §1.1 test still applies.

does a minor repair need approved data?

No. A minor repair runs on the acceptable standard of §43.13(a), where the manufacturer’s maintenance manual or Instructions for Continued Airworthiness are the prescribed source of methods. What it still needs is a method traceable to a source that satisfies the Administrator, and a record entry that describes the work or references that data.

who classifies the repair?

The organization performing it, on a record, and before the work begins. There is no external classification service to wait for, which is precisely why the decision needs a defined owner and a written basis rather than a conversation at the bench.

what happens if a repair is misclassified as minor?

The work may be sound and the release will still be defective, because §145.201(c) conditions approval for return to service on the applicable data standard having been met. Correcting it afterwards means obtaining approved data for work already performed, which is harder than obtaining it beforehand and occasionally impossible.


Classification is the cheapest decision in the whole sequence and the one that constrains every other. Make it against the appliance subdivision of Appendix A, record which limb of the §1.1 test you relied on, and the question of who signs the data answers itself before anyone opens the component.

About AeroKool Aviation. AeroKool Aviation is an FAA-certificated repair station in Hialeah, Florida, specializing in the repair and overhaul of environmental control system components — air cycle machines, cooling turbines, heat exchangers, refrigeration packages, valves and environmental control units — for commercial, regional, business jet, rotorcraft and military operators. The company was founded in 1959 and holds AS9110C and AS9100D registrations, with in-house PMA parts manufacturing and FAA DER repair engineering. Its engineering, manufacturing and repair management programs are described on the site, and component capability is organized by aircraft category, manufacturer, model and component type in the component capability listing, down to individual part numbers such as this air cycle machine for a legacy narrow-body platform.

This article is general technical information about the classification of repairs and alterations as major or minor under the Federal Aviation Regulations. It is not approved data, it is not a maintenance procedure, and it does not replace the component maintenance manual, structural repair manual, service bulletin, airworthiness directive or other airworthiness data your organization is approved to use. Regulations, advisory material and manufacturer data are revised, and how a specific finding is classified depends on the article, the nature of the work and the scope of the repair station’s certificate. Verify the classification and its data basis against the current text of Part 1 and Part 43, your own quality system, and a properly authorized DER, an ODA holder or your FAA principal inspector before performing or accepting any maintenance action.

Talk to AeroKool Aviation

AeroKool Aviation is an FAA-certificated repair station in Hialeah, Florida, overhauling air cycle machines, cooling turbines, heat exchangers, valves and environmental control units for commercial, regional, business and military operators since 1959, with an AS9110C quality system and in-house PMA and DER engineering. If you have a component on the bench, a repeat removal you cannot explain, or a part number you cannot source, we will tell you what falls inside our ratings and what does not. Request a quote with the part number and the register the aircraft is on, and the answer will name the data basis.

Address
1495 S.E. 10th Avenue Hialeah, FL 33010-5984
eMail
aerokool@aerokool.com | sales@aerokool.com
Phone
305.887.6912 | 800.458.4255

Scroll to Top

Have Questions Or Need Information?

Please fill out the form below to contact us and we will get back to you as soon as possible.
Request a Quote
Choose one for Sales and Repair Services
We're committed to your privacy. AeroKool Aviation uses the information you provide to us to contact you about our relevant content, products, and services. You may unsubscribe from these communications at any time. For more information, check out our Privacy Policy.

Looking for parts?

You can search by Part Number or Aircraft Model

Search for Parts

Browse our extensive inventory

Note: You can search by part number

Your Aircraft

Browse our extensive inventory

Note: You can search by aircraft name