Hawker 400 cooling turbine on a bench with an evaluation report, illustrating a beyond economical repair declaration

Beyond Economical Repair Aircraft Components: What the Declaration Rests On and What Happens Next

By the AeroKool Aviation team · Hialeah, Florida

Beyond economical repair aircraft components are units that a shop or an operator has declared not worth restoring, and the declaration is a commercial judgment backed by evidence, not an airworthiness finding. A unit can be repairable in a technical sense and still be declared beyond economical repair, and a unit can be declared so on evidence that does not hold up.

The abbreviation BER hides both possibilities, and the phrase beyond economical repair aircraft components is used for both. It reads like a diagnosis, and it works like a price decision. The difference matters when the unit is a repeat removal, because a BER declaration closes the unit and may leave the cause of the removals untouched.

This guide explains what the declaration rests on, who makes it and who decides, what happens to the unit afterward, and which questions to put to a BER report before accepting it.

It is written for the operator, fleet engineer, or buyer who receives the declaration and has to act on it. It contains no cost thresholds, percentages, or limits, because none of the sources cited in this guide sets them. For the pattern that makes the declaration costly, see why aircraft component repeat removals persist.

The site already covers the wider choice between repairing and replacing in repair or replace for aircraft components. That decision starts with the options open. This guide starts later, after an evaluation has reached a conclusion about one specific unit, and asks what the conclusion rests on and who owns it.

What Beyond Economical Repair Means for an Aircraft Component

A Declaration About One Unit

A BER declaration is made about a specific serial number at a specific moment, on the evidence available then. It is not a statement about the part number or the component family. Another unit of the same part number, with different findings, can be economical to repair.

The declaration compares what restoring the unit would involve with what the owner is prepared to spend or accept. Both sides of that comparison have to be written down for the declaration to be read by anyone else.

A Commercial Term, Not a Regulatory One

None of the sources cited in this guide defines beyond economical repair, and none sets the point at which a repair stops being economical. Shops, operators, and lessors each use the term in their own way, sometimes with a percentage of replacement value in a contract and sometimes with no stated basis at all.

That is why the written definition of beyond economical repair aircraft components matters in a contract. A BER figure with no stated basis is a conclusion the reader cannot check.

How It Differs From the Repair-or-Replace Decision

Repair or replace is a decision between options, made with the choices still open. A BER declaration is the result of an evaluation that has already found those options wanting for this unit. The first asks what to do, and the second states what the evaluation concluded.

The two can contradict each other. An operator that has decided to repair as a policy can receive a BER declaration for a unit, and the gap between the two is a conversation to be had with the evidence in hand.

What the Declaration Depends On

Findings From the Teardown

The declaration begins with what the shop found when it opened the unit. A BER finding that is not tied to teardown findings is an opinion. The teardown report is the record that the declaration should be traced back to, and it should be requested when the evaluation is ordered.

The findings also say whether the damage belongs to the unit. A unit that was damaged by something else may be declared BER and then replaced by another that suffers the same fate, as a damage pattern that traces to another component would show.

The Repair Route Available

Whether a repair is possible depends on the manufacturer data and on what the shop is approved to do. A repair that exists in the data can be priced, and a repair that has to be engineered is a different kind of conclusion.

14 CFR §43.13 calls for the manufacturer’s current maintenance manual or other methods acceptable to the Administrator, and the record should say which route the evaluation considered. Choosing between overhauled, rebuilt, and repaired covers the words the record can defend when a route is chosen.

The shop’s ratings matter here too. A shop that is not approved for a given article cannot declare the repair route closed on the unit’s behalf, only that it cannot take it. The shop’s published capability list shows what it is approved for, and it should be read before the declaration is.

The Comparison the Owner Sets

The other side of the declaration is the comparison point: the cost of a replacement, an exchange unit, or a unit from stock. The owner sets that, not the shop, and it can change with availability. A declaration made when replacements were easy to find may not hold when they are not.

Ask which comparison was used and when it was set. A BER finding that was correct against one price list can be wrong against another.

The same applies to lead time. A unit that is cheaper to replace than to repair on paper can be the more expensive choice if the replacement is not available when the aircraft needs it, and that trade-off belongs in the declaration if it was part of the decision.

Who Makes the Declaration and Who Decides

The Shop Evaluates, the Owner Decides

The shop’s role is to evaluate the unit and report what restoring it would involve. The decision to stop belongs to the owner of the unit. A shop that declares BER has told the owner what it found, and the owner has to decide what to do with that.

This is also why the report matters. An owner who receives a declaration with no findings, no route, and no comparison has no way to decide anything.

Why the Operator’s Responsibility Does Not Move

14 CFR §121.363 provides that a Part 121 certificate holder is primarily responsible for the airworthiness of its aircraft and that arranging for another person to perform maintenance does not relieve it of that responsibility. A BER declaration by a shop is therefore an input to the operator’s own decision, and it does not replace it. Outside Part 121, confirm the allocation in your contract.

What Happens to the Unit After the Declaration

Return, Retain, or Dispose Is a Contract Question

The sources cited in this guide do not say who owns a unit after a BER declaration or what must be done with it. That is set by the order, the contract, and the owner’s instructions. The shop should state what it will do with the unit if no instruction arrives, and the owner should state it before the unit is evaluated.

A unit that is returned should come back with the findings. A unit that is retained or disposed of should leave a record of what happened to it.

The same applies to the paperwork around the declaration. How to evaluate an aircraft component repair quote covers what the estimate should show before a unit is declared uneconomical, and what to ask about a repair warranty covers what stands behind a repair that is carried out.

Life-Limited Parts and Condemned Parts

14 CFR §43.10 provides that anyone who removes a life-limited part from a type-certificated product must ensure it is controlled by one of the listed methods, so that it cannot be reinstalled after it reaches its life limit. The listed methods include a record keeping system, a tag or record attached to the part, marking, segregation, and mutilation.

A BER declaration on a unit that contains such parts raises the question of how they are controlled, and the answer comes from the section and from the data for the part number. The unserviceable tag covers how that information travels with a unit.

A condemned unit also raises a supply question. If it can re-enter the supply chain without a clear record of its status, it becomes a risk for someone else. Suspected unapproved parts explains why status has to follow the part.

Common Nonconformities and Failure Points

A Declaration With No Findings

The report says the unit is BER and does not say what was found. The owner cannot test the conclusion, and a later repeat removal cannot be compared with what was seen. The first question to ask is which findings the declaration rests on.

A Figure With No Stated Basis

The declaration cites a cost or a percentage with no statement of what it includes or what it was compared with. The same repair can be economical or not depending on the basis, and the reader has no means of telling which applies.

A Declaration That Closes the Cause

The unit is condemned, replaced, and the file ends. If the damage came from the installation or a neighboring component, the replacement inherits it. The investigation of the pattern should continue after the unit is condemned.

What a BER Declaration Does Not Settle

“A BER Unit Is Scrap”

A BER declaration says the owner is not going to restore the unit. It does not say that the unit has no value or that it is to be destroyed. The unit can have a use as a source of data, as a core, or as evidence in an investigation, depending on the contract and the owner’s decision.

What the declaration changes is the unit’s status in the owner’s records. That status has to be written down and has to travel with the unit.

A unit whose status is unclear is a problem for the next person who handles it. The declaration is only useful if the record says plainly what the unit is now.

“BER Is Decided by Price Alone”

Price is one side of the comparison. The other is what the evaluation found, what repair route exists, and what the owner has chosen to compare against. A declaration that cites price and nothing else has left out the part that would let anyone check it.

Questions to Ask Before You Accept a BER Declaration

These questions make a declaration readable. Put them in the order, the evaluation request, or the quote.

A shop that can answer them has written the declaration to be checked. A shop that cannot has told you how much weight to give it.

  • Which findings from the teardown does the declaration rest on?
  • Which repair route did the evaluation consider, and under what data?
  • What comparison was used, who set it, and when?
  • What is the status of the unit now, and who owns it?
  • Does the unit contain life-limited parts, and how are they controlled?
  • What happens to the unit if no instruction is given?

Start with the part number. If the unit is a cooling turbine such as the Hawker 400 cooling turbine 586110-9, that number ties the declaration to one set of manufacturer data and one set of findings. The published capabilities by aircraft and component type show which part numbers sit in the scope AeroKool Aviation publishes, and a part number outside the published list is a question to ask, not an assumption to make.

The published programs page lists repair and overhaul, PMA and DER, manufacturing, engineering, and repair management and logistics. The contact form is where the part number and the removal history go.

Frequently Asked Questions

What does beyond economical repair mean?

It means that the owner or the shop has concluded that restoring a specific unit is not worth the cost, on the evidence available. None of the sources cited in this guide defines the term, so a contract that uses it should say what it means.

Is beyond economical repair the same as unrepairable?

No. A unit can be repairable and still declared BER because of cost, availability of an alternative, or the owner’s decision. A unit that cannot be repaired within the approved data is a different statement, and the report should say which one applies.

Who decides that a unit is beyond economical repair?

The owner decides, with the shop’s evaluation as input. For a Part 121 certificate holder, 14 CFR §121.363 leaves primary responsibility for airworthiness with the operator even when another person performs the maintenance.

What should a BER report contain?

The unit and its serial number, the teardown findings, the repair route considered and the data it relies on, the comparison used and when it was set, and the status and ownership of the unit afterward. This guide does not set the figures, because they belong to the contract and the owner.

What happens to a unit after it is declared beyond economical repair?

That depends on the order and the contract. If the unit contains life-limited parts, 14 CFR §43.10 applies to how they are controlled once removed, and the record should show the unit’s status.

Does a BER declaration end the investigation of a repeat removal?

No. It ends the repair of that unit. If the cause is outside the unit, the replacement will meet it again, so the declaration should feed the investigation and not close it.

A BER declaration is a decision about a unit and a record of what it rested on. If the file cannot show the findings, the repair route, and the comparison behind it, the owner has accepted a figure without being able to check it.

About AeroKool Aviation. AeroKool Aviation is an FAA-certificated repair station in Hialeah, Florida, specializing in the repair and overhaul of environmental control system components — air cycle machines, cooling turbines, heat exchangers, refrigeration packages, valves and environmental control units — for commercial, regional, business jet, rotorcraft and military operators. The company was founded in 1959 and holds AS9110C and AS9100D registrations, with in-house PMA parts manufacturing and FAA DER repair engineering. Read more in the company profile.

This article is general technical information about how beyond economical repair declarations for aircraft environmental control system components are made, documented and acted on. It is not approved data, it is not a maintenance procedure, and it does not replace the component maintenance manual, structural repair manual, service bulletin, airworthiness directive or other airworthiness data your organization is approved to use. Regulations, standards and manufacturer data are revised, and the requirements that apply to a specific job depend on the part number, the aircraft, the operator’s approved program and the scope of the repair station’s certificate. Verify the applicable requirements against the current manufacturer data, your own quality system, your contract, and your FAA principal inspector or EASA competent authority before performing or accepting any maintenance action.

Talk to AeroKool Aviation

AeroKool Aviation is an FAA-certificated repair station in Hialeah, Florida, overhauling air cycle machines, cooling turbines, heat exchangers, valves and environmental control units for commercial, regional, business and military operators since 1959, with an AS9110C quality system and in-house PMA and DER engineering. If you have a component on the bench, a repeat removal you cannot explain, or a part number you cannot source, we will tell you what falls inside our ratings and what does not.

Address
1495 S.E. 10th Avenue Hialeah, FL 33010-5984

eMail
aerokool@aerokool.com | sales@aerokool.com

Phone
305.887.6912 | 800.458.4255

Scroll to Top

Have Questions Or Need Information?

Please fill out the form below to contact us and we will get back to you as soon as possible.
Request a Quote
Choose one for Sales and Repair Services
We're committed to your privacy. AeroKool Aviation uses the information you provide to us to contact you about our relevant content, products, and services. You may unsubscribe from these communications at any time. For more information, check out our Privacy Policy.

Looking for parts?

You can search by Part Number or Aircraft Model

Search for Parts

Browse our extensive inventory

Note: You can search by part number

Your Aircraft

Browse our extensive inventory

Note: You can search by aircraft name